更新咖啡壶塑料为木头

Coffee Pot Upgrade
setp.1
爱动手
Trace the Handle Trace the outline of the original handle onto the wood.
setp.2
爱动手
Drill Holes I used a 3/16th diameter brad point bit to drill a series of holes around the traced outline. I like brad point bits for this task because their sharp points keep them from slipping when you drill holes right next to each other. I cut out most of the handle but left a small piece connected to the large piece of wood so that it would be easier to clamp and sand.
setp.3
爱动手
Carve I clamped the wood to my work table and used the carving burr to shape the handle.
setp.4
爱动手
Sand Once I hade the rough shape of the handle, I switched to the sanding drum and smoothed down the handle.
setp.5
爱动手
Finish Cutting Off the Handle After shaping the handle, I cut it off from the larger piece of wood with a drill. I used a knife to clean up a few of the drill marks.
setp.6
爱动手
Finish Cutting Off the Handle After shaping the handle, I cut it off from the larger piece of wood with a drill. I used a knife to clean up a few of the drill marks.
setp.7
爱动手
Sand I used 120 and then 320 grit sandpaper to finish the handle.
setp.8
爱动手
Stain I finished the walnut with a coat of Danish oil.
setp.9
爱动手
Cut Out the Top Knob I didn't like the design of the original knob because it was too close to the stainless steel and my knuckles would bump into the hot kettle when I would try and remove the lid. I drew a completely new profile for the wooden knob and cut it out with the drill.
setp.10
爱动手
Cut Out the Top Knob I didn't like the design of the original knob because it was too close to the stainless steel and my knuckles would bump into the hot kettle when I would try and remove the lid. I drew a completely new profile for the wooden knob and cut it out with the drill.
setp.11
爱动手
Carve + Sand I carved and finished the knob the same way as the handle.
setp.12
爱动手
Remove Plastic Handles I drilled a series of small holes through the plastic handle and then used wire cutters to clip away the plastic between the holes.
setp.13
爱动手
Remove Plastic Handles I drilled a series of small holes through the plastic handle and then used wire cutters to clip away the plastic between the holes.
setp.14
爱动手
Install New Handle I drilled two holes in the walnut handle to accommodate the coffee pot's metal prongs. The handle fit on securely, but a 2-part epoxy can be used if you don’t achieve a tight fit.
setp.15
爱动手
Install New Handle I drilled two holes in the walnut handle to accommodate the coffee pot's metal prongs. The handle fit on securely, but a 2-part epoxy can be used if you don’t achieve a tight fit.
setp.16
爱动手
Install New Handle I drilled two holes in the walnut handle to accommodate the coffee pot's metal prongs. The handle fit on securely, but a 2-part epoxy can be used if you don’t achieve a tight fit.
setp.17
爱动手
Install New Handle I drilled two holes in the walnut handle to accommodate the coffee pot's metal prongs. The handle fit on securely, but a 2-part epoxy can be used if you don’t achieve a tight fit.
setp.18
爱动手
Screw On Top Knob The original plastic knob for the Hario kettle screws off. I drilled a hole into the new wooden knob and screwed it onto the lid. Good luck making your own coffee pot upgrade and please email or tweet photos to @benuyeda or ben@homemade-modern.com. For more detailed instructions, dimensioned drawings and different variations of the project, check out our soon-to-be-released book.
setp.19
爱动手
Screw On Top Knob The original plastic knob for the Hario kettle screws off. I drilled a hole into the new wooden knob and screwed it onto the lid. Good luck making your own coffee pot upgrade and please email or tweet photos to @benuyeda or ben@homemade-modern.com. For more detailed instructions, dimensioned drawings and different variations of the project, check out our soon-to-be-released book.
setp.20
爱动手
Screw On Top Knob The original plastic knob for the Hario kettle screws off. I drilled a hole into the new wooden knob and screwed it onto the lid. Good luck making your own coffee pot upgrade and please email or tweet photos to @benuyeda or ben@homemade-modern.com. For more detailed instructions, dimensioned drawings and different variations of the project, check out our soon-to-be-released book.
setp.21
爱动手
Screw On Top Knob The original plastic knob for the Hario kettle screws off. I drilled a hole into the new wooden knob and screwed it onto the lid. Good luck making your own coffee pot upgrade and please email or tweet photos to @benuyeda or ben@homemade-modern.com. For more detailed instructions, dimensioned drawings and different variations of the project, check out our soon-to-be-released book.
via
~ THE END ~

使用的工具与材料

  • 爱动手的心
  • 喜欢动手的人

Copyright© 2014-2019, SStudio. All rights reserved. 闽ICP备15004573号-1